Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Blog Article
What're your thoughts about Installing A Bathtub?

Installing a tub isn't precisely brain surgery, but it does require solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably difficult job. If the old tub is readily available, the project can move speedily; if you have to open up a wall to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to move out the old tub and embeded in the new one. Make certain you have actually qualified on your own for the task and fit attempting it. Instead of employing a service provider to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you might need an expert plumber to make tube links.
This article will certainly assist you install a brand-new tub in your bathroom if you have currently purchased a brand-new tub and also do not require to change the arrangement of your previous water supply pipelines.
Your devices and also product checklist should make up the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath ought to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be quite bothersome as a result of the limited accessibility that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Before carrying on to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the needed setting. The wood boards are helpful in equally spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bathtub up until the level reads degree.
To install taps, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the water as well as examine all joints and brand-new pipework for leakages and tighten them if essential. Fill the tub as well as also inspect the overflow outlet as well as the regular electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the bath tub should wait up until the bath tub has been made use of a minimum of when as this will certainly settle it right into its last position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washers are in location between the tap and the sink. Protect the faucet in position with the producer given backnut. As soon as the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The former type should be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to split a rigid seal, triggering the water to permeate the wall surface between the bath and the tiling, resulting in issues with moisture and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the tub remains in use. The sealant can crack fairly early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the marketplace. It is suggested to fit the tiles making use of waterproof or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I'm certainly very fascinated by How to Install a Bathtub Yourself and I hope you enjoyed our blog entry. If you enjoyed reading our article plz make sure you remember to pass it around. Kudos for your time. Please check our website back soon.
Leaks? Contact us! Report this page